NASCAR Heat - Build Race Setups: Description
User Avatar Image

DusterLag
Member / Driver
Offline Offline
 
Message
 
Posts: 8108
Joined: May 1, 2010



Tire Pressure

Lower tire pressures result in a more forgiving car, and result in higher tire temperatures. Higher pressures allow higher top speeds with less temperature buildup. The recommended pressure will keep the middle (M) temperature of the tires near the average of the inside (I) and outside (O) temperatures. Going higher than recommended can result in more speed at a high-speed track, but the loss in grip can hurt at slower tracks.

Raise R/F Loosens car off the corner.
Lower R/F Tightens car up
Raise R/R Tighter into corner looser off
Lower R/R Looser on short runs, as heat builds tightens up. (Think of those long runs)
Raise L/F Tightens car up into and off the corner.
Lower L/F Looser off the corners.
Raise L/R Looser off the corners but tighter in the middle.
Lower L/R Looser at start but tightens up on long runs.

Shock Bump

At the front, a lower number (softer shock compression) loosens the car during the transition to braking, and at the rear, softer shock compression tightens the car during the transition to throttle. Higher numbers (stiffer shock compression) give quicker reactions during these transitions, and the opposite effects.

Shock Rebound

At the front, a lower number (softer shock rebound) loosens the car during the transition to throttle, and at the rear, softer shock rebound tightens the car during the transition to braking. Higher numbers (stiffer shock rebound) give quicker reactions during the transitions, and the opposite effects.

Raise R/F Tighter off the corner.
Lower R/F Looser off the corner.
Raise R/R Looser from the middle and off the corner.
Lower R/R Tighter from the middle and off the corner.
Raise L/F Also tighter from the middle off.
Lower L/F Looser into corners if done in combination with raising r/r.
Raise L/R Looser in and off corner.
Lower L/R Tightens car up off corners.

Springs

Softer front springs usually loosen the car (turns better), while softer rear springs tighten it (less likely to spin). Use the softest springs you can without letting the car scrape the ground. If the car rolls too much, stiffen the sway bars.

Raise R/R Loosens car into corners.
Lower R/R Tightens car off corner.
Raise L/R Tightens car off corner.
Lower L/R Loosens car in the middle to off corner.

Camber

Some positive left side and negative right side camber will help the car turn left. Too much camber will reduce grip and increase tire wear. Tire temperatures on the edge of the tire leaning into the turn (outside -O- on left, inside -I- on right) should be 5 to 10 degrees hotter than the other edge. Negative equal cambers on both sides are usually best on a road coarse, with inside temperatures 5 to 10 degrees hotter than outside.

Front Brake Bias

If the car doesn't turn well under braking, decrease the front brake bias. If it wants to spin under braking, increase the front brake bias. Go with the lowest front bias you can control.

Front Sway Bar

Stiffening the front sway bar (larger diameter) tightens the car and reduces body roll when cornering, which can give better control over the tire camber during cornering. Too stiff a bar can lift a front wheel off the track when cornering.

Rear Sway Bar

Stiffening the rear sway bar (larger diameter) loosens the car and reduces body roll when cornering.

Final Gear Ratio

The final gear ratio is used to adjust all four gears together. A smaller ratio allows for higher top speeds, but produces less torque at the rear wheels, so it will take longer to reach top speed.

Transmission Gear Ratios

Allows each gear to be individually adjusted. A smaller ratio allows for higher top speeds, but produces less torque at the rear wheels, so it takes longer to reach top speed. DON'T FORGET, once you set the individual gear ratio, it will act accordingly to a change in the final gear ratio.

Grill Tape

More tape reduces air drag and increases front down force, but can cause engine overheating.

Spoiler

Less spoiler reduces air drag and rear down force, giving higher top speeds and a looser car. A setting of 70% is mandated at the super-speedways.

Front Weight Bias

Shifting weight to the front (a higher front bias) can help the car turn in better, but may give more mid-corner push. Shifting weight back can stabilize the car at turn entry, but may loosen in mid-corner.

Left Weight Bias

On an oval, use the maximum left weight allowed. On road courses, it's usually best to keep the weight equal on the left and right sides.

Wedge

Less wedge will loosen the car, allowing it to turn better. More wedge tightens the car, and can help in putting the power down. On a road course, use 50% wedge to keep the car from pulling to the left or right under power.

<< Edited on Saturday, September 17, 2016 at 4:15pm EDT. >>
Activity
There are currently 0 users and 16 guests online. We have a total of 15527 posts in 4025 topics within 24 forums.

Users Browsing: None